62
edits
m (Make it explicit that axies are for HID nintendo) |
m (DualShock4 and DualSense use the same axis) |
||
(11 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
Dolphin supports the motion [https://en.wikipedia.org/wiki/Evdev evdev] devices but setting it up is a bit awkward. Nintendo Switch controllers (Joy-Con and Pro controller) are supported through the hid-nintendo driver. Sony DualShock 4 and DualSense through hid-sony/hid-playstation. | |||
The HID kernel driver exposes 2 (or more) evdev devices, one for the buttons and another for the accelerators/gyroscopes. The hid-nintendo driver exposes the motion axis on an "IMU" device while hid-playstation named it "Wireless Controller Motion Sensors". Do note that Nintendo Joy-Cons will have 2 devices each (4 in total). | |||
You may need to add the users to a specific group to be allowed access. On Arch Linux this group is ''input''. | |||
It took me a bit of time figuring out which axis corresponds with the right motion control in Dolphin. '''These axis might change in the future when evdev standardizes them. | |||
''' | |||
{| class="wikitable" | {| class="wikitable" | ||
!Dolphin motion | !Dolphin motion | ||
! | !Switch controllers | ||
!Sony DualSense/DualShock4 | |||
|- | |- | ||
|Accel Up | |Accel Up | ||
|Accel Z+ | |Accel Z+ | ||
|Accel Y+ | |||
|- | |- | ||
|Accel Down | |Accel Down | ||
|Accel Z- | |Accel Z- | ||
|Accel Y- | |||
|- | |- | ||
|Accel Left | |Accel Left | ||
|Accel Y+ | |Accel Y+ | ||
|Accel X- | |||
|- | |- | ||
|Accel Right | |Accel Right | ||
|Accel Y- | |Accel Y- | ||
|Accel X+ | |||
|- | |- | ||
|Accel Forward | |Accel Forward | ||
|Accel X+ | |Accel X+ | ||
|Accel Z- | |||
|- | |- | ||
|Accel Backward | |Accel Backward | ||
|Accel X- | |Accel X- | ||
|Accel Z+ | |||
|- | |- | ||
|Pitch Up | |Pitch Up | ||
|Gyro Y- | |Gyro Y- | ||
|Gyro X+ | |||
|- | |- | ||
|Pitch Down | |Pitch Down | ||
|Gyro Y+ | |Gyro Y+ | ||
|Gyro X- | |||
|- | |- | ||
|Roll Left | |Roll Left | ||
|Gyro X- | |Gyro X- | ||
|Gyro Z+ | |||
|- | |- | ||
|Roll Right | |Roll Right | ||
|Gyro X+ | |Gyro X+ | ||
|Gyro Z- | |||
|- | |- | ||
|Yaw Left | |Yaw Left | ||
|Gyro Z+ | |Gyro Z+ | ||
|Gyro Y+ | |||
|- | |- | ||
|Yaw Right | |Yaw Right | ||
|Gyro Z- | |Gyro Z- | ||
|Gyro Y- | |||
|} | |} | ||
Line 54: | Line 65: | ||
[[File:Select_imu_device.png]] | [[File:Select_imu_device.png]] | ||
Select the corresponding Accel or Gyro axis, select it and click | Select the corresponding Accel or Gyro axis, select it and click OK. For example for ''Accel Up'' in Dolphin you need to select ''Accel Z+''. The end result should look like below. | ||
[[File:Advanced_config_result.png]] | [[File:Advanced_config_result.png]] | ||
Repeat this for every motion. | Repeat this for every motion. | ||
[[Category:Tutorials]] |